# Need help wiring Sensirion SPS30 to NodeMCU ESP8266 (AirRohr firmware)

**URL:** <https://forum.sensor.community/t/need-help-wiring-sensirion-sps30-to-nodemcu-esp8266-airrohr-firmware/8378>\
**Category:** Uncategorized\
**Created:** [April 16, 2026, 8:41pm UTC](https://forum.sensor.community/t/need-help-wiring-sensirion-sps30-to-nodemcu-esp8266-airrohr-firmware/8378 "2026-04-16T20:41:59Z")\
**Posts on this page:** 6\
**Page:** 1

<div class="post-metadata">

**Author:** ![Michael](https://forum.sensor.community/letter_avatar_proxy/v4/letter/m/4bbf92/32.png) [@Michael](https://forum.sensor.community/u/Michael)\
**Post date:** [April 16, 2026, 8:41pm UTC](https://forum.sensor.community/t/need-help-wiring-sensirion-sps30-to-nodemcu-esp8266-airrohr-firmware/8378/1 "2026-04-16T20:41:59Z")

</div>

Hi everyone,

I’m currently trying to set up an air quality monitoring system using a NodeMCU ESP8266 V3 and a Sensirion SPS30 fine dust sensor.

I have already flashed the firmware using the AirRohr flashing tool, and now I’m at the stage where I need to connect the SPS30 sensor. I’m using a SparkFun breadboard-to-JST-ZHR cable, but I’m unsure about the correct wiring and pin assignment.

Could someone please help me with:

- The correct pinout for connecting the SPS30 to the NodeMCU ESP826 using the AirRohr firmware

- Any important details I should be aware of (voltage levels, firmware version, etc.)

I want to make sure I don’t damage the sensor or the board.

Thanks in advance for your help!

---

<div class="post-metadata">

**Author:** ![pjg](https://forum.sensor.community/user_avatar/forum.sensor.community/pjg/32/194_2.png) [@pjg](https://forum.sensor.community/u/pjg)\
**Post date:** [April 17, 2026, 5:23am UTC](https://forum.sensor.community/t/need-help-wiring-sensirion-sps30-to-nodemcu-esp8266-airrohr-firmware/8378/2 "2026-04-17T05:23:39Z")

</div>

### SPS30 (I2C, 5V)

Pinout: 1 2 3 4 5

- Pin 1 (5V) → Pin VU/VIN

- Pin 2 (SDA) → Pin D3 (GPIO0)

- Pin 3 (SCL) → Pin D4 (GPIO2)

- Pin 4 (SEL) → Pin GND

- Pin 5 (GND) → Pin GND

---

<div class="post-metadata">

**Author:** ![pjg](https://forum.sensor.community/user_avatar/forum.sensor.community/pjg/32/194_2.png) [@pjg](https://forum.sensor.community/u/pjg)\
**Post date:** [April 17, 2026, 5:25am UTC](https://forum.sensor.community/t/need-help-wiring-sensirion-sps30-to-nodemcu-esp8266-airrohr-firmware/8378/3 "2026-04-17T05:25:15Z")

</div>

Don’t forget to adapt the configuration in the sensor interface and in devices.sensor.community.

---

<div class="post-metadata">

**Author:** ![Michael](https://forum.sensor.community/letter_avatar_proxy/v4/letter/m/4bbf92/32.png) [@Michael](https://forum.sensor.community/u/Michael)\
**Post date:** [April 24, 2026, 5:36pm UTC](https://forum.sensor.community/t/need-help-wiring-sensirion-sps30-to-nodemcu-esp8266-airrohr-firmware/8378/4 "2026-04-24T17:36:10Z")

</div>

Thanks a lot, I got the SPS30 running with your configuration 😀!

---

<div class="post-metadata">

**Author:** ![istvan](https://forum.sensor.community/letter_avatar_proxy/v4/letter/i/3da27b/32.png) [@istvan](https://forum.sensor.community/u/istvan)\
**Post date:** [July 8, 2026, 9:44am UTC](https://forum.sensor.community/t/need-help-wiring-sensirion-sps30-to-nodemcu-esp8266-airrohr-firmware/8378/5 "2026-07-08T09:44:59Z")

</div>

Hi, I have a question on this wiring setup:

According to [this](https://sensor.community/en/sensors/airrohr/) guide, D3 and D4 are used for the BME280. Where would I connect the BME280 sensor in this case?  
Thanks for advice!

---

<div class="post-metadata">

**Author:** ![serber](https://forum.sensor.community/letter_avatar_proxy/v4/letter/s/e79b87/32.png) [@serber](https://forum.sensor.community/u/serber)\
**Post date:** [July 8, 2026, 2:46pm UTC](https://forum.sensor.community/t/need-help-wiring-sensirion-sps30-to-nodemcu-esp8266-airrohr-firmware/8378/6 "2026-07-08T14:46:58Z")

</div>

You can connect multiple sensors to SCL/SDA (D3,D4) pins at same time
